ds oil skimmer unimag

DS OIL SKIMMER

VIEW MORE DETAIL

DESCRIPTION 

1. Disk Oil Skimmer removes floating oil on coolant surface by plate, preventing coolant from deterioration.
2. Equipped with oil/water separating tank, removing floating oil only and clean coolant draining back to coolant tank.

SPECIFICATION 
Plate is made from stainless steel, diameter is 300mm, 400mm, or 500mm. Motor position is either left or right side, easy to be installed.

Read More

Magnetic separator Unimag MSJD

Double Driven Super Magnetic Separator

Description

1.  Ferrous contaminant can be attacted, pressed, and discharged automatically. No filter media consumption in the coolant filtration system. 
2. The Double Driven Super Magnetic Separator adds sprockets on the sides of gum roller, so it will never be slippery with oil coolant.  
3. It can attract contaminants with weak magnetic force, such as cemented carbide and carbon.

Magnetic separator MSJD

 View More Details

Features

1. Use Rare Earth Magnets, 8 times of magnetic force stronger than Ferrite Magnets. 
2. No magnetic force near scraper, so contaminant is easy to be discharged. Upper scraper can be adjusted if worn down.

  Specification

1. Capacity: 20-300L/MIN. 
2. Stainless Steel frame. Motor's position can be on eith left or right side.  
3. Position of fluid outlet is on left, right side, or bottom.

 

Read More

Magnetic Separator Unimag MSK

EASY SUPER

MAGNETIC SEPARATOR

View More Detail

DESCRIPTION 

We provide Coolant Filtration System, Magnetic Separator and Super Easy Scrape Magnetic Separator with high quality.

1. Taiwan Coolant Filtration Supplier. 
2. Ferrous contaminant can be attracted, squeezing, and discharged automatically. No filter media consumption in the coolant filtration system.  
3. Use rare earth magnets, whose magnetic force is 8 times stronger than Ferrite magnets.

FEATURES

1. It can attract contaminants with weak magnetic force, such as cemented carbide, carbon.
2. It works excellently with oil coolant. Second filtration process is not necessary. 
3. No magnetic force near scraper, so contaminants are easy to be discharged. 
4. You can adjust the upper scraper while it is wearing.

SPECIFICATION

1. Capacity: 20, 30, 40, 60, 80, 100, 150, 180, 240,300L/MIN.
2. Stainless Steel frame. Motor's position can be on either left or right side. 
3. Position of fluid outlet is on left, right side, or bottom.

Read More

Magnetic separator Unimag MCJ

Duck Magnetic Separator Suppliers

Duck Magnetic Separator equipped with a magnetic roller that attracts contaminants from coolant, then dried and discharged. No filter media consumption in the Coolant Filtration System.

View More Details

Duck Magnetic Separator

FEATURES

1. Ferrous contaminant can be attacted, pressed, and discharged automatically. No filter media consumption.
2. Use superior ferrite permanent magnets and by test magnetic circuit design, the attractive forces are the best among similar products. 
3. External area of magnetic drum is filled with magnetic force, perform best in filtration process.
4. Frame is die-cast by aluminum-alloy. Super appearance and leak-proof. Un-attractive to magnetic force (except MCJ-240A). 
5. The magnetic drum can attract the impurities from the coolant. After squeezing, it can be discharged automatically and witout any consumption. 
6. You can adjust the upper scraper while it is wearing. 
7. If you want to filter the carbide, carbon remover of headened steel and oil coolant. we suggest you to purchase super magnetic separator MCJ-**HK.

Specification :

• Applicable to Machines:
• Surface Grinder
• Centerless Grinder
• Internal/External Grinder
• Honing Machine
• Thread Grinding Machine 
• Gear Grinding Machine 
• Polisher
• Filtration Efficiency: 50 Micron
• Capacity: 40L/Min-240L/min

 

Read More

Magnetic Chip Conveyor Chip Conveyor With Filtration Effect

MCC

Magnetic Chip Conveyor , Chip Conveyor With Filtration Effect

View More Details

DESCRIPTION
The Magnetic Chip Conveyor is installed between machining center and oil tank. Chips smaller than 60mm are attracted by permanent magnets that rotate inside the Magnetic Chip Conveyor, and then transported andraised. Chips contain only minimum oil and then drop into a chip box.

Specification

• Width(W), Length(L), and Height of chip outlet(H) can be customized.

Other 1

• Increasing speed improves capacity.

 

Read More

Dust Collector

Dust And Mist Collector

DESCRIPTION 

1. High-efficient revolving impeller works and use rough, middle, fine and HEPA multilevel filtration material to filter dust and mist. Filtration efficiency reaches 99.97%. Themultilevel of filtration material can filter mist and dust through cutting and grinding process, no block and filtration material easy to be replacement. 
2. The reusable rough filtraion material can be cleaned.

View More Detail

Features

The Dust And Mist Collector can solve the problem as following:
1. Allergy and headache caused by sucking mist and dust.
2. Injuries because mist and dust sprayed on the ground make workers silp accidentally.
3. Reduction of productivity: Workers lack working will in the place around dust and mist.
4. Environment pollution and energy waste
5. Fire sensor lose function while covered by mist and oil. 5. Electric cabinet of machine tools damages.

Read More

Coolant Through Spindle series

BF830-CTS

Coolant Through Spindle Series

CTS High Pressure Device

 

 

 View More Details

 DESCRIPTION
This series of CTS High Pressure Device features its excellent performance.

1. Applicable to machining center with Coolant Through the Spindle (CTS). Small space occupied (only 815*815mm) 
2. Two sets of 8"*30"bag filter units for primary filter, filtering capacity is 5-10 micron; on-line bag-changing. 
3. Equipped with level switch; auto water-supplementary; light alarm while at abnormal.

Specification

1.  Recommend: 1 HP water-supplementary pump, which is 60LPM of flowrate and 3 kg/cm2 of pressure. 
2. High-pressure flowrate: 30LPM(60HZ) or 26LPM(50HZ). High pressure pump acpacity: 5 HP at 50kg/cm2 of pressure, and 7.5HP at 70 kg/cm2 of pressure. 
3. Apply the WANNER(USA) rotary diaphrapm pump, which allow for an impurity below 0.5mm.

Read More

Candle Filter Unimag

CFMP

Portable Candle Filter

CFMP

   View More Details

DESCRIPTION

Filtration efficiency: 1~3 micron, suitable for coolant of EDM and tool grinder.

 

 

Features

1. Coolant Filtration system for EDM and grinding fluid.
2. Each candle-like filter element is composed of thousands of thin wafers and composed tightly by springs. When dirty fluid passes through tiny gaps between wafers, all prticles over one micron is trapped on the outside edge of filter elements. Filter efficiency reaches 1~3 micron. 
3. Automatically cleaned by a rapid backwash cycle. Use air to blow out particles trapped on elements and then deposit them into a sludge collecting basket.
4. The replaceable filter elements’ life lasts several years. (Please use recommended circulation oil.)

 

Read More

Magnetic Separator MCA SERIES

Magnetic Separator Suppliers

DESCRIPTION

1.  The Magnetic Separator is suitable for heavy duty grinding. 
2. No filtration media consumption in the Coolant Filtration System. 
3. The lowest cost for purchasing Coolant Filtration System. 
4. Easy to fit in other Filtration Devices as a previous filtration process.

View More Detail

Specification :

Capacity: 240-1000L/MIN.

Read More

Magnetic Separator

 MAGNETIC SEPARATOR 

Read More

side cutting pliers long nose

SIDE CUTTING PLIERS, LONG NOSE PLIERS, etc

 

Part number
■ 1050/1050 J (Tipe standar)

■ 2050 (dengan tipe leverage tinggi)

■ 6050 (dengan jenis lengan crimping)

■ 2080N (tipe Slim)

■ XP200 (untuk pekerjaan listrik)

■ 2060N (dengan tipe leverage tinggi dan dengan crimping sleeve)

■ 105 / 105H (tang pemotong sisi panjang)

■ 150 (tang potong sisi hidung panjang / tipe langsing)

■ ZA185 (tang sekrup)

■ Y75 (tang hidung semi-panjang tugas berat)

■ 2500R (tang hidung panjang jangkauan)

■ 2500T (tang kuku untuk perbaikan ban)

Feature




[1050H-200] kawat baja φ3.2mm, kawat tembaga φ4mm.

[2050-185] kawat baja φ3.2mm, kawat tembaga φ4mm.

[2050-225] kawat baja φ3.6mm, kawat tembaga φ4.5mm.

[6050-185] kawat baja φ2.6mm, kawat tembaga φ3.5mm.

[2080N-185] kawat baja φ3.2mm, kawat tembaga φ4mm.




[2080N-210] kawat baja φ3.6mm, kawat tembaga φ4.5mm.

[XP200] kawat baja φ3.6mm, kawat tembaga φ4.5mm.




[2060N] kawat baja φ3.2mm, kawat tembaga φ4mm.

[105-150 / 105H-150] kawat baja φ1.5mm, kawat tembaga φ2.6mm.

[105-175 / 105H-175] kawat baja φ2mm, kawat tembaga φ3mm.

[150-150] kawat baja φ1.2mm, kawat tembaga φ2mm.

Read More

duct and mould cutters

DUCT AND MOULD CUTTERS

 

Part number

• SX15 (standard type)
• SX25 (long blade type)
• DX80 (ratchet type)
• DK55 / DK65 (end cutting type)

 Feature

Blade, plastic plate, spring can be replaced easily.
Cleanly cut section.

Blade type:
[X15] for SX15.
[X25] for SX25.
[X80] for DX80.

Plastic plate type:
[PB-SX15] for SX15.
[PB-SX25] for SX25.

Spring type:
[MBN-12] for SX15.

Cutting capacity:
[DK55 / DK65] φ8mm.

Read More

miniature nipper

MINIATURE NIPPERS & PLIERS

Part number

• 01 (miniature nippers)
• 02 (miniature nippers / tip edge type)
• 03 (miniature nippers)
• 04 (miniature nippers / blade back side scooped out)
• 05 (miniature nippers / with stripping hole)
• 06 (miniature needle pliers)
• 07 (miniature bent nose pliers)
• 08 (miniature flat nose pliers)
• 09 (miniature semi needle pliers)
• M10 (miniature long needle pliers)
• M11 (miniature plastic cutting nippers)
• M12 (miniature plastic cutting nippers)
• M13 (miniature needle pliers / serrated)
• M14 (miniature side cutting pliers / serrated)
• M15 (miniature chain nose pliers)
• M16 (miniature end cutting nippers)
• PC1 (PC forming pliers / for bending lead wires)
• PC2 (PC forming pliers / for bending lead wires)
• PC3 (PC bent nose pliers / for grasping in narrow and deep spaces)
• PC4 (PC nippers / for cutting in narrow spaces)
• PC5 (PC nippers / for cutting beyond certain articles)
• PC6 (PC end cutting nippers / for cutting in deep spaces)

Feature

with opening spring.

Cutting capacity:
[01 / 02 /03 / 04 / 05 / M16 / PC6] steel-wire φ0.5mm, copper-wire φ0.8mm.

[M14] steel-wire φ1.2mm, copper-wire φ2mm.
[M11 / M12] soft-resin φ3mm.
[PC4] steel-wire φ0.9mm, copper-wire φ1.6mm.
[PC5] steel-wire φ0.7mm, copper-wire φ1.6mm.

View More Details

Read More

plastik pipe cutter

PLASTIC PIPE CUTTERS (SNIP)

Part number

• PIP19 (Standard type)
• PIP20 (Heavy-duty type)
• PIP7Z (Slim type)
• PIP42 (Easy operation type)

 Feature

Operasi satu tangan untuk memotong pipa plastik.
Dapat memotong raceway permukaan plastik pada sudut yang diinginkan dengan attachment terpasang. (untuk PIP19 / PIP42)

Blade dapat dikunci dengan Stopper saat tidak bekerja demi keamanan. (untuk PIP42)
Pembukaan blade dengan menekan Release Lever. (untuk PIP42)

Cutting capacity:


[PIP19 /PIP42]φ42mm (Standard vinyl pipe VP30, Water pipe VW30, Electric wiring pipe VE36.)
[PIP7Z]φ26mm (Standard vinyl pipe VP20, Water pipe VW20, Electric wiring pipe VE22.)
[PIP20]φ63mm (Standard vinyl pipe VP50, Water pipe VW50, Electric wiring pipe VE54.)

Blade type:

[P18Z] for PIP19.
[P42] for PIP42.
[P7] for PIP7Z.
[P20] for PIP20.

Overall length:
[PIP19]217mm.
[PIP42]220mm.
[PIP7Z]185mm.
[PIP20]325mm.

View More Details  

Read More

Perawatan Cubicle

Cubicle dipasang  disisi Gardu Listrik dan berfungsi sebagai Pembagi, Pemutus, Penghubung dan Proteksi system instalasi listrik 20 KV
Cubicle biasanya dipasang didalam ruang gardu Distribusi listrik.

Cubicle ada beberapa macam:

1. Cubicle  LBS (Load Break Switch)
2. Cubicle PMS (Pemisah)
3.  Cubicle CB Out Metering 
4. Cubicle TP (Transformer Protection)
5. Cubicle  PT (Potential Transformer)
6. Cubicle B1 ( Terminal Out Going)

Untuk  menjaga kehandalan Cubicle, maka perlu dilakukan Perawatan Rutin
Lingkup Perawatan Cubicle meliputi:

1. Pemeriksaan  Rutin
2. Pemeliharaan Rutin
3. Prediktive Maintenance
4. Perbaikan atau Penggantian Part
 

Read More

heat nipper

 HEAT NIPPERS (FOR CUTTING PLASTICS)

Part numbe

• HT180 (Standard type)
• HT200 (Heavy-duty type)
• HT120 (End cutting type)
• HT130 (Long blade type)
• HT140 (Flat blade type)
• HT160 (for cutting narrow spaces)
• HT170 (Angle blade type)
• HT180DX (Standard type / with sensor)

                                                                           Feature

Pemanas built-in menghangatkan tepi pisau untuk memotong lebih mudah, bebas retak bahan rapuh seperti akrilik, plastik styrene, dan resin kaca.

Heat nipper ini harus digunakan dengan transformator yang sesuai.
Cutting capacity:
[HT180 /HT120 /HT130 /HT140 /HT160 /HT170 /HT180DX]φ4mm.
[HT200]φ7mm.

Heater type:
[W19] for HT180 /HT120 /HT130 /HT140 /HT160 /HT170 /HT180DX.
[W29] for HT200.

Transformer type:
[TRF25-100V] for HT180 /HT120 /HT130 /HT140 /HT160 /HT170 /HT200.
[TRF25-220V] for HT180 /HT120 /HT130 /HT140 /HT160 /HT170 /HT200.
[TRF25-240V] for HT180 /HT120 /HT130 /HT140 /HT160 /HT170 /HT200.
[TRF100D] for HT180DX.

Step-Down Transformer type:
[HDT100] for TRF25-100V .

Read More

nippers

MUROMOTO NIPPERS

Part number

• 205 / 205H (jepit daya tinggi untuk memotong kawat baja)
• 206S (jepitan flush cut untuk memotong kawat halus)
• 55S (electric nippers)
• 55SPM (electric nippers with holding type))
• XN200 (nippers for electrical work)
• 305 (nippers for hard wire)
• 405 (end cutting nippers)
• 450 (standard nippers)
• 550 (angle cutting nippers)
• WA1000 (compound cutting nippers)
• CT55 (carbide tipped nippers)
• CT305 (carbide tipped nippers)

Feature

 Cutting capacity:

[205-150 / 205H-150 / 206S-150] steel-wire φ2mm, copper-wire φ2.6mm.
[205-175 / 205H-175 / 206S-175] steel-wire φ2mm, copper-wire φ3mm.
[205-200 / 205H-200 / 206S-200] steel-wire φ2.6mm, copper-wire φ3.5mm.
[55S-120 / 55SPM-120] steel-wire φ0.8mm, copper-wire φ1.2mm.
[55S-150 / 55SPM-150] steel-wire φ1.5mm,
copper-wire φ2.6mm.
[XN200] steel-wire φ2.6mm, copper-wire φ3.5mm.
[305-7] steel-wire φ2.6mm, copper-wire φ3.5mm.
[305-8] steel-wire φ3.2mm, copper-wire φ4mm.
[405-7] steel-wire φ2mm, copper-wire φ3mm.
[405-8] steel-wire φ2.4mm, copper-wire φ3.2mm.
[405-9] steel-wire φ2.6mm, copper-wire φ3.5mm.
[450-125] steel-wire φ0.8mm, copper-wire φ1.2mm.
[450-150] steel-wire φ1.5mm, copper-wire φ2.6mm.
[550S-125] steel-wire φ0.9mm, copper-wire φ1.2mm.
[550-150] steel-wire φ1.6mm, copper-wire φ2mm.
[WA1000] steel-wire φ2mm, copper-wire φ2.6mm.
[CT55-120 / CT55-150] piano-wire φ0.5mm.
[CT-305-7] piano-wire φ1mm.
[CT305-8]  piano-wire φ1.2mm.

View More Details 

Read More

cutting plastik

PLASTIC NIPPERS

Part number

• 160S (high-plastic nippers / round type blade)
• 160SF (high-plastic nippers / flat type blade)
• 160SA (high-plastic nippers / angle type blade)
• 160FW (high-plastic nippers / extra thin blade)
• 66S (plastic nippers)
• 99 / 99S / 99SF (heavy-duty plastic nippers)
• 170S (angled plastic nippers)
• WA1000F (compound action plastic nippers)
• 68S (narrow nose plastic nippers)
• PG20 (pin gate plastic nippers)
• 2000EF / 23EF / 24EF / 25EF /26EF (end cutting plastic nippers)
• 550SF (angle cutting plastic nippers)
• L40 (long handle plastic nippers)
• M11 / M12 (miniature plastic cutting nippers)

 Feature

for nearly flush cutting of moulded plastic components from sprues.
with opening spring.

Cutting capacity:
[160S-125 / 160SF-125 / 160SA-125] φ3mm.
[160S-150 / 160SF-150 / 160SA-150] φ5mm.
[M11 / M12] φ3mm.
[160FW-125] φ2mm.
[160FW-150] φ4mm.
[66S-150] φ5mm.
[99-150 / 99S-150 / 99SF-150] φ8mm.
[99-175 / 99S-175 / 99SF-175] φ9mm.
[99-200 / 99S-200 / 99SF-200] φ10mm.
[170S-150] φ5mm.
[WA1000F] φ5mm.
[68S-125] φ2mm.
[PG20-125] φ1mm.
[2000EF / 23EF / 24EF / 25EF / 26EF] φ3mm.
[550SF-125] φ3mm.
[550SF-150] φ5mm.
[L40-190] φ5mm.
[M11 / M12] φ3mm.

Read More

pneumatic level gauge manufacturers

LG-40

Pneumatic Level Gauge Manufacturers

View More Details 

DESCRIPTION

   Pneumatic Level Gauge is to detect level in a open tank, especially for dirty or sticky fluid. Low cost and long life.

Features

1. The Pneumatic Level Gauge detects difference of air pressure and pushes diaphragm and limited switch. 
2. Very easy to install on tanks's top.

Specification

1.  Enlarge detecting tube when encounting high-viscosity fluid., or smaller tube will cause late reflection.
2. Applicable to temparature from 0-60 degree.

Read More

Oil Skimmer Belt

BELT OIL SKIMMER OSA

Belt Oil Skimmer

 

 View More Details

DESCRIPTION
In addition to Net Type Oil Skimmer, we also offer Super Magnetic Sludge Separator and Belt Type Oil Skimmer. Floating oil on coolant surface is removed by a stainless steel net, preventing coolant from deterioration.

FEATURES

The Net Type Oil Skimmer is equipped with oil/water separating tank, removing floating oil only and clean coolant draining back to coolant tank.

Specification

• Stainless steel net: 100mm, Motor: 25W, Speed reducing motor ratio: 1/180 (specific specification is available)

Read More

Hydrocylone unimag

HYDROCYCLONE

Hydrocyclone

 View More Details

DESCRIPTION
Hydrocyclone is a device using pump to supply pressure and high speed to inject coolant into tube of a special design where ascending/descending vortexes are created. Clean coolant will be drained out through ascending vortex while impurities will be precipitated by descending vortex. Excellent filtration effect up to 98%; low maintenance and long duration. The Coolant Filtration System is especially applicable to centerless grinder.

 

 

 Features 

1. Long duration- tungsten shaft of pump and lower nipple of ceramic material. Easily replacable with bare bands.
2. Separate contaniments from coolant, reducing water replacement frequency and triming demand for grinding wheel, and producing smoother workpiece surface. 
3. Ideal for filtering ferrous and nonferrous materials.

Read More

air shears nile muromoto

MUROMOTO AIR SHEARS

       Part number

AS100 (standard type)
AS200 (standard type)
ASP150 (heavy-duty type)
ASP250 (heavy-duty type)
AM10 (machine-fitting type)
AM20 (machine-fitting type)


      Feature 
AIR SHEARS AS100
Length(less blade):140mm   Weight: 230g   Grip size: 36φmm   Air consumption:137㎤/stroke   Air pressure: 0.5～0.6MPa   Blade type: No.100S, No.100R   Cutting capacity: (plate) 0.5×15mm

AIR SHEARS AS200
Length(less blade): 182mm   Weight: 500g   Grip size: 45φmm   Air consumption:227㎤/stroke   Air pressure: 0.5～0.6MPa   Blade type: No.200S, No.200R   Cutting capacity: (plate) 0.8×25mm, 1.0×10mm

AIR SHEARS ASP150
Length(less blade): 212mm   Weight: 300g   Grip size: 36φmm   Air consumption:274㎤/stroke   Air pressure: 0.5～0.6MPa   Blade type: No.100S, No.100R   Cutting capacity: (plate) 0.5×20mm

AIR SHEARS ASP250
Length(less blade): 269mm   Weight: 720g   Grip size: 45φmm   Air consumption:508㎤/stroke   Air pressure: 0.4～0.6MPa   Blade type: No.200S, No.200R   Cutting capacity: (plate) 0.8×25mm, 1.0×15mm

AIR SHEARS AM10
Length(less blade): 129mm   Weight: 296g   Grip size: 36□mm   Air consumption:137㎤/stroke   Air pressure: 0.5～0.6MPa   Blade type: No.100S, No.100R   Cutting capacity: (plate) 0.5×15mm

AIR SHIARS AM20
Length(less blade): 159mm   Weight: 507g   Grip size: 45□mm   Air consumption:227㎤/stroke   Air pressure: 0.5～0.6MPa   Blade type: No.200S, No.200R   Cutting capacity: (plate) 0.8×25mm, 1.0×10mm

Air Shears Optional Blades:
[No.100S, No.100R] for AS100, ASP150, AM10
[No.200S, No200R] for AS200, ASP250, AM20
(※No.100S, No.200S : Blade tip pointed)
(※No.100R, No200R : Blade tip round)

View More details 

Read More

air fil saws nile muromoto

MUROMOTO AIR FIL-SAWS

 Part number

AF10S ( Stroke : 10mm )
AF7 ( Stroke : 7mm )
AF7S ( Stroke : 5mm )

 Feature

AIR FIL SAWS AF10S
Panjang: 201mm Berat: 750g Ukuran pegangan: □ 39 × 37mm Konsumsi udara: 280ℓ / menit Tekanan udara: 0.65MPa Kecepatan reciprocating: 5.500 stroke / menit Kapasitas pemotongan:

Plat logam 1mm: 1.000mm / menit Plat logam 3mm: 180mm / menit
AIR FIL SAWS  AF7 / AF7S
Panjang: 180mm Berat: 650g Ukuran pegangan: □ 39 × 37mm

Konsumsi udara: 280ℓ / menit Tekanan udara: 0.65MPa

Kecepatan reciprocating:

(AF7) 6,900 stroke / menit (AF7S) 8,400 stroke / menit

Kapasitas pemotongan:
(AF7) 1mm pelat logam: 900mm / mnt Plat logam 3mm: 135mm / mnt

(AF7S) 1mm pelat logam: 850mm / mnt Plat logam 3mm: 135mm / mnt


Ringan dan sunyi dalam pengoperasian.

Lubang masuk pelumas diatur agar mudah dilumasi.

Mudah menyesuaikan aliran udara.

Tidak ada getaran antara kepala dan dudukan untuk getaran minimum.

Selang udara lunak digunakan untuk pengoperasian yang nyaman.

Efisiensi pemotongan dan penyelesaian yang lebih  terjamin.

Accessories:
Saw blade

1. Steel straight cut type (AF1032). 2 pieces.
2. Steel circle cut type (R1032). 1 piece.

Files

1. Flat type (AFF50). 1 piece.
2. Round type(AFR50). 1 piece.
3. Triangular type(AFT50). 1 piece.

Optional accessories:
Saw blade

1. Steel straight cut type (AF1032). 10 pieces.
2. Steel circle cut type (R1032). 10 pieces.
3. Steel small-circle cut type (SR1036). 10 pieces.
4. Urethane bumper cut type (R1010). 10 pieces.
5. Timber Aluminium cut type(W1014). 10 pieces.

Files

1. Flat type (AFF50). 1 piece.
2. Round type(AFR50). 1 piece.
3. Triangular type(AFT50). 1 piece.

View More details 

Read More

mini belters muromoto

MUROMOTO MINI BELTERS

Part number

MB20S (standard type)
MB20 (for use in limited places or for spot sanding)
MB25 (lever type, belt width 20mm)
MB25S (lever type, belt width 10mm)

                                                      Mini Belters Feature

3-point belt supporting system offers easier and more smooth sanding operation for better finish.

• Mini Belters MB20S (standard type)

Length:290mm   Weight:1,080g   Air consumption:300l/min   Air pressure:0.5～0.6MPa   Free belt speed:2,200m/min   Belt size:20mm×520mm

• Mini Belters MB25 (for rear exhaust and for lever type, belt width 20mm)

Length:780mm   Weight:1,480g   Air consumption:300l/min   Air pressure:0.5～0.6MPa   Free belt speed:2,200m/min   Belt size:20mm×520mm

• Mini Belters MB25S (for rear exhaust and for lever type, belt width 10mm)

Length:780mm   Weight:1,350g   Air consumption:300l/min   Air pressure:0.5～0.6MPa   Free belt speed:2,200m/min   Belt size:10mm×520mm

2-point belt supporting system offers easier and more smooth sanding operation for better finish.

• Mini Belters MB20 (for use in limited places or for spot sanding type)

Length:290mm   Weight:930g   Air consumption:300l/min   Air pressure:0.5～0.6MPa   Free belt speed:2,200m/min   Belt size:20mm×520mm

Applications:
Sanding for various auto-repair services such as…
removing spot welding, removing paint off flat or curved surfaces, removing adhesives, removing welding bead.
Finishing wood work.
Deburring small metal products.
General finishing work.
Removing rust.
Other sanding and polishing work.

Optional accessories:
Abrasive cloth belts (Sanding belt of zirconia zesin)

• 40 (20 pieces): for MB20S, MB25, MB20
• 60 (20 pieces): for MB20S, MB25, MB20
• 100 (20 pieces): for MB20S, MB25, MB20
• 60-10 (20 pieces): for MB25S
• 100-10 (20 pieces): for MB25S

View More Details  

 

Read More

curl hose

MUROMOTO CURL HOSE

      Part number

• Curl Hose (standard type)
• Curl Hose (with straight hose type)
• Jumbo Curl Hose (G type)
• Mini Curl Hose (M type)
• Straight Hose (UH type)
•  Thickly Rolled Curl Hose (CHL type)
• Curl Hose (SE type)
• Curl Hose (GS type)
• Strech Curl Hose
• Large Diameter Strech Curl Hose
• Bala Curl

◎ Penampilan: Diameter luar adalah Ф28mm (tipe standar); karena itu ringan dan mudah di gunakan.
◎ Fleksibilitas: Fleksibel dan ringan （1/3 dari selang karet）; oleh karena itu pengoperasian genggaman mudah dan membuat pekerjaan Anda ringan.
◎ Elastisitas: Ini memiliki karakteristik tolakan tinggi dan dapat bertahan lama digunakan.
◎ Ketahanan aus: Ketahanan aus adalah 3-5 kali dari selang karet.
class="tlid-translation translation" lang="id">◎ Resistansi kimia ： Kecuali asam klorida, asam fosfat, asam sulfat, asam nitrat, dan soda kaustik, metil klorida, klor-aldehida non-manusia. Itu menggunakan bahan untuk yang terbaik yang bisa bertahan paling lama (30 hari direndam)
◎ Heat resistant：Up to 70 °C
◎ Tahan dingin: Tidak merusak fleksibilitas bahkan dalam kondisi -10 ° C
-10 ° C
◎ Tahan tekanan: Ini akan mentoleransi uji ekspansi dan kontraksi 300.000 kali atau lebih dalam tekanan udara 0.7MPa.
◎ Utilitas: Peralatan silinder, Pistol semprot pelapis, Peralatan industri, Mesin makanan, Peralatan medis, Alat pneumatik Umum.

View More Details

Read More